Designed for the Finnish M39, this Scout Scope Mount also works as an “universal fit” for most milsurp Mosin Nagant variants.

Like our very successful Mauser Mount, this mount features the proven Anchor Point concept of attachment by utilizing the recoil lug and rear sight ladder pivot hole.

See product review here: Guns and Tactics Magazine

“ANCHOR POINT” Series – See Through Design

• Innovative “Anchor Point” design provides superior stability
• See through design for continued use of fixed iron sights
• Installs in minutes, no permanent modification required
• No straight bolt handle or stripper clip interference
• No contact with stock
• Recoil lug nut spanner wrench included
• Unit comes loosely preassembled
• Rigid all steel construction, include 5/16” x 8” MIL-STD 1911 Picatinny Rail
• Made in America, 100% Lifetime Warranty

*This mount fits the majority of all Mosin Nagant variant designs. PLEASE READ FITMENT NOTES BEFORE PURCHASING!

 Why consider a “Scout” type setup for your rifle?

A LER (Long Eye Relief) optic, or Scout Scope, mounted forward of the receiver provides a substantial uninterrupted overall field of view. This unconfined environment results in greater situational awareness allowing for fast target acquisition and shots taken with both eyes open. This configuration has additional advantages for bolt action MilSurp (military surplus) rifle platforms as it does not interfere with spent casing ejection, straight bolt handles or stripper clip use.

FEATURES:

Product provides for mounting of scout scope or other long eye relief (LER) optics to Mosin Nagant rifles without the need to drill and tap the receiver or make any permanent modifications to firearm. It is designed to use the recoil lug attachment point and rear sight ladder pivot attachment point allowing for the continued use of the original fixed/iron sights.

SPECIFICATIONS:

The mount will accommodate a front to back (horizontal) distance of _” (_mm) to _” (_mm) from the center of the recoil lug to the center of the rear sight block ladder pivot. It also allows for an up and down (vertical) distance of _” (_ mm) to _” (_ mm) from the same. The rear sight riser block is designed to fit over rear sight blocks that measure a maximum of _” (_ mm) wide. The total weight including hardware is 9.5 oz. However, the net weight increase is only 8.7 oz. due to the replacement of the original recoil lug bar and nut.

INCLUDED: Hex body spanner wrench for recoil lug nut IS included. All necessary hardware, hex wrenches and complete installation instructions.

MOUNT DOES NOT INCLUDE SCOPE & RINGS!

FITMENT NOTES:

We have made every reasonable effort to ensure that this product will fit the majority of Mosin Nagant rifle variants. However, due to the large number of these firearms produced over many years around the world, it is impossible for us to allow for all manufacturing variation. As with any of our products, it may be returned undamaged for a full refund. The mount can only accommodate so much misalignment. You should measure the center distances as described in the SPECIFICATIONS to ensure that the mount will fit properly. Proper tightening of all hardware should result in no movement of the mount during normal firing recoil.

NOTE:

Any scope or mount that suffers an impact should not be trusted to be accurate. If you feel your mount has been compromised you can still use your original open iron sights. Design subject to change without prior notice. Caution! Improper installation or use may result in damage to property, severe injury, or loss of life. If for any reason this product does not function properly, discontinue use immediately. Always practice proper SAFETY and ensure an UNLOADED condition before beginning installation.

Please call us at 828-665-4427 with any installation questions you may have.

DUE TO AVAILABILITY, WE REGRET THAT WE CAN NO LONGER OFFER THE MOUNT/SCOPE COMBINATION AT A DISCOUNTED PRICE. SCOPES ARE SOLD SEPERATELY HERE.

The post Brass Stacker™ Finnish M39 Mosin Nagant Universal Fit Scout Scope Mount appeared first on Brass Stacker.

***PLEASE READ SPECS & FITMENT NOTES BEFORE PURCHASING***

There is no need for bent bolt handle with this mount.

Why consider a “Scout” type setup for your rifle?

A LER (Long Eye Relief) optic, or Scout Scope, mounted forward of the receiver provides a substantial uninterrupted overall field of view. This unconfined environment results in greater situational awareness allowing for fast target acquisition and shots taken with both eyes open. This configuration has additional advantages for bolt action MilSurp (military surplus) rifle platforms as it does not interfere with spent casing ejection, straight bolt handles or stripper clip use.

FEATURES:

Allows for mounting of Scout Scope or other long eye relief optics on your milsurp Mosin Nagant without the need to drill & tap receiver or make any permanent modifications to the firearm. It is designed to fit over rear sight block in order to allow for continued use of the original fixed/iron sights up to 100 meters. Mount and MIL-STD 1913 Picatinny 8″ rail are rigid steel construction with Black Oxide finish. 100% Lifetime Warranty!

FITS:

M44, M38, T53 and M53

SPECIFICATIONS:

This Mount utilizes the barrel pin hole and the pivot pin hole in the rear sight block. The Mount will accommodate a front to back (horizontal, parallel to bore axis) pin center distance of 1.56″  (39.6mm) to 1.79″ (45.4mm) and allows for an up and down (vertical, perpendicular to bore axis) pin center distance of .18″  (4.6mm) to .41″ (10.3mm). The Mount is designed to fit over rear sight blocks that measure between .750″ (19.05mm) and .787″  (20.00mm) wide. The total weight including hardware is 5.4 oz. We have made every reasonable effort to ensure that this product will fit the majority of M38, M44 & T53’s. However, due to the large number of these firearms produced over many years around the world, it is impossible for us to allow for all manufacturing variation. Bolts are Grade 12.9 medium carbon Q&T alloy steel hardened to Rc 38-44 and have a tensile strength of 177000 psi. Tightening torque is 1.67 ft lbs. Proper tightening of all hardware should result in no movement of the mount during normal firing recoil. If for any reason our Mount does not work with your specific variant it can be returned (undamaged) for a full refund.

INCLUDED: All necessary hardware, hex wrench, drill (provided to clean out or straighten existing pin holes), punch (light duty punch not designed for difficult to remove pins such as those soldered) and complete installation instructions.

MOUNT DOES NOT INCLUDE SCOPE & RINGS!

FITMENT NOTES:

This mount will NOT work for a M91/30 or M91/59! See Model MN9130SSM for a M9130, M9159.

The pin hole in the rear sight block is often located inconsistently as a result of the original manufacturing process. The pin hole, relative to the pivot pin, is frequently not parallel and may be out of alignment or skewed. The Mount can only accommodate so much of this misalignment. You should measure the center distances from barrel pin to pivot pin on both sides and check those with the dimensions listed in the SPECIFICATIONS to ensure that the mount will fit properly. A 3mm drill is provided and can be used to clean out and straighten (to some degree) without enlarging the barrel pin hole once the pin is removed. The barrel pin hole and pivot pin hole in the rear sight block are generally .118″ (3.0mm) in diameter and the supplied 3mm bolts have a nominal OD of .115″ (2.92mm). This tight fit along with the use of an appropriate liquid thread locker for the screws and nuts, as well as proper tightening of the same should result in no movement of the Mount during normal firing recoil.

NOTE:

A MAPP (Methyl Acetylene Propadience Propane) gas torch and heavy duty punch may be required to remove existing pins from the rear sight block if they are soldered in place. You can usually find these items at your local hardware or plumbers supply. The application of heat, if done properly, will not cause damage. Keep in mind that you only need to reach the melting point of the solder and that this same temperature was achieved during original construction without adverse effects. Procedure provided in supplied instructions.

Any scope or mount that suffers an impact should not be trusted to be accurate. If you feel your mount has been compromised you can still use your original open iron sights. Design subject to change without prior notice. Caution! Improper installation or use may result in damage to property, severe injury, or loss of life. If for any reason this product does not function properly, discontinue use immediately. Always practice proper SAFETY and ensure an UNLOADED condition before beginning installation.

Please call us at 828-665-4427 with any installation questions you may have.

DUE TO AVAILABILITY, WE REGRET THAT WE CAN NO LONGER OFFER THE MOUNT/SCOPE COMBINATION AT A DISCOUNTED PRICE. SCOPES ARE SOLD SEPERATELY HERE.

The post Mosin Nagant M38 M44 T53 Scout Scope Mount ONLY appeared first on Brass Stacker.

***PLEASE READ SPECS & FITMENT NOTES BEFORE PURCHASING***

There is no need for bent bolt handle with this mount.

Why consider a “Scout” type setup for your rifle?

A LER (Long Eye Relief) optic, or Scout Scope, mounted forward of the receiver provides a substantial uninterrupted overall field of view. This unconfined environment results in greater situational awareness allowing for fast target acquisition and shots taken with both eyes open. This configuration has additional advantages for bolt action MilSurp (military surplus) rifle platforms as it does not interfere with spent casing ejection, straight bolt handles or stripper clip use.

FEATURES:

Allows for mounting of Scout Scope or other long eye relief optics on your military surplus Mosin Nagant model M91/30 and M91/59 without the need to drill & tap receiver or make any permanent modifications to the firearm. It is designed to fit over rear sight block in order to allow for continued use of the original fixed/iron sights up to 100 meters. Mount and MIL-STD 1913 Picatinny 8″ rail are rigid steel construction with Black Oxide finish. 100% Lifetime Warranty!

Fits:

M9130, M9159

SPECIFICATIONS:

The Mount will accommodate a front to back (horizontal) pin center distance of 1.39″ (35.3mm) to 1.82″ (46.7mm) and allows for .039″ (1mm) of up and down (vertical) movement. The Mount is designed to fit over rear sight blocks that measure between .750″(19.05mm) and .787″(20.00mm) wide. The total weight including hardware is 5.5 oz. We have made every reasonable effort to ensure that this product will fit the majority of M9130’s. However, due to the large number of these firearms produced over many years around the world, it is impossible for us to allow for all manufacturing variation. Bolts are Grade 12.9 medium carbon Q&T alloy steel hardened to Rc 38-44 and have a tensile strength of 177000 psi. Tightening torque is 1.67 ft lbs. Proper tightening of all hardware should result in no movement of the mount during normal firing recoil. If for any reason our Mount does not work with your specific 9130 it can be returned (undamaged) for a full refund.

INCLUDED: All necessary hardware, hex wrench, drill (provided to clean out or straighten existing pin holes), punch (light duty punch not designed for difficult to remove pins such as those soldered) and complete installation instructions.

MOUNT DOES NOT INCLUDE SCOPE & RINGS!

FITMENT NOTES:

This mount will NOT work for the M38, M44 or T53. Nor will it work for an M91 with Chatellerault or Konovalov type rear sight block! See Model MN384453SSM for a M38, M44 or T53.

The pin holes in the rear sight block are often located inconsistently as a result of the original manufacturing process. The two holes are frequently not parallel to each other and may be out of alignment or skewed. The mount can only accomodate so much of this misalignment. You should measure the center distances from pin to pin on both sides and check those with the dimensions listed in the SPECIFICATIONS to ensure that the mount will fit properly. A 3mm drill is provided and can be used to clean out and straighten (to some degree) without enlarging the pins holes once the pins are removed. The pin holes for the rear sight block are generally .118″(3.0mm) in diameter and the supplied 3mm bolts have a nominal OD of .115″(2.92mm). This tight fit along with the use of an appropriate liquid thread locker for the screws and nuts, as well as proper tightening of the same should result in no movement of the Mount during normal firing recoil. Occasionally the rear sight block itself, as it sits on the barrel dovetail underneath, can be out of alignment with the bore axis. This condition, if extreme, can adversely effect how the Mount sits. Please note that some rifles may have pins holding the rear sight block to the barrel soldered in place. Instructions for correctly applying the required heat to remove the solder are provided for use at consumer’s discretion. Also, some may have pins that require the use of substantial force to remove. This should be done with a heavy duty punch (not supplied). The supplied light duty punch is NOT designed for difficult to remove pins.

Please refer to mount “Specifications” to determine the acceptable amount of deviation for the conditions listed below. IMPORTANT! If your rifle has a condition as described below that will not allow the MN9130SSM Mount to work… please see our MN39SSMR Universal Fit Anchor Point Series mount.

FIGURE 1) A single pin holding the rear sight block to the barrel will not allow the MN9130SSM mount to attach properly. **The mount can be used as a template to drill a second hole with the supplied drill bit at consumer’s discretion.
FIGURE 2) Pins not perpendicular or skewed to bore centerline can result in the MN9130SSM mount not fitting properly.
FIGURE 3) Pins not the same distance from bore centerline can result in an unacceptable degree of up or down “Pitch” making the MN9130SSM mount hard to level front to back.
FIGURE 4) A rear sight block that does not run parallel with bore centerline can result in an unacceptable degree of right or left “Yaw” making the MN9130SSM mount lead off to one side.
FIGURE 5) Pins higher on one side from bore centerline than the other side can result in an unacceptable degree of “Roll” making the MN9130SSM mount hard to level side to side.

NOTE:

A MAPP (Methyl Acetylene Propadience Propane) gas torch and heavy duty punch may be required to remove existing pins from the rear sight block if they are soldered in place. You can usually find these items at your local hardware or plumbers supply. The application of heat, if done properly, will not cause damage. Keep in mind that you only need to reach the melting point of the solder and that this same temperature was achieved during original construction without adverse effects. Procedure provided in supplied instructions.

Any scope or mount that suffers an impact should not be trusted to be accurate. If you feel your mount has been compromised you can still use your original open iron sights. Design subject to change without prior notice. Caution! Improper installation or use may result in damage to property, severe injury, or loss of life. If for any reason this product does not function properly, discontinue use immediately. Always practice proper SAFETY and ensure an UNLOADED condition before beginning installation.

DUE TO AVAILABILITY, WE REGRET THAT WE CAN NO LONGER OFFER THE MOUNT/SCOPE COMBINATION AT A DISCOUNTED PRICE. SCOPES ARE SOLD SEPERATELY HERE.

The post Mosin Nagant M9130, M9159 Scout Scope Mount ONLY appeared first on Brass Stacker.

“ANCHOR POINT” Series – See Through Design

• Innovative “Anchor Point” design provides superior mount stability
• See-thru design for continued use of fixed iron sights
• No permanent modification of firearm required*
• Allows for complete field stripping without mount removal*
• Will not interfere with stripper clip use*
• Does not contact stock
• Casing Deflector available for long tube optics
• Rigid all steel construction, includes 5/16” x 3-5/16” Picatinny Rail
• Cross bolt nut spanner wrench is included
• Unit comes loosely preassembled
• Made in America with a 100% Lifetime Warranty

Why consider a “Scout” type setup for your rifle?

A LER (Long Eye Relief) optic, or Scout Scope, mounted forward of the receiver provides a substantial uninterrupted overall field of view. This unconfined environment results in greater situational awareness allowing for fast target acquisition and shots taken with both eyes open. This configuration has additional advantages for bolt action MilSurp (military surplus) rifle platforms as it does not interfere with spent casing ejection or stripper clip use.

*Please note certain restrictions as follows: Mount for use with original wooden stocks. Lack off “interference” applies to “mount” only. Optic interference (with disassembly of gas tube or use of stripper clip) may occur depending on optic type, optic length/diameter, ring height, etc. Compact, red dot or reflex type optics can typically be positioned avoiding any interference. Stripper clips CANNOT be used in conjunction with Casing Deflector. PLEASE READ FITMENT NOTES BEFORE PURCHASING! If you intend to use a long tube optic, the Casing Deflector  (model # SKSCD) is highly recommended.

FEATURES: Product provides for the mounting of scout scope, red dot / reflex type or other long eye relief (LER) optics to SKS rifles without the need to drill and tap the receiver or make any permanent modifications to firearm. It is designed to use the cross bolt (sometimes referred to as the recoil lug) as the primary attachment point and securely installs over rear sight block.

FITS:

Russian 45, Chinese Type 56 (Non-Norinco) and Yugoslavian 59/66

Unit is shipped with a variant specific cross bolt.

SPECIFICATIONS: The mount will accommodate a front to back (horizontal) distance of approximately 1-5/8″ to 1-3/4″ from the center of the cross bolt to the center of the rear sight block ladder pivot. It also allows for an up and down (vertical) distance of approximately 1-9/16″ to 1-15/16″ from the same. The total weight is 5.8 oz.

INCLUDES: All necessary hardware, hex body cross bolt nut spanner wrench, required hex wrenches and installation instructions.

MOUNT DOES NOT INCLUDE DEFLECTOR OR SCOPE & RINGS!

FITMENT NOTES:

We have made every reasonable effort to ensure that this product will fit the majority of SKS rifle variants (Russian 45, Chinese Type 56 [non Norinco], Yugoslavian 59/66, etc.). However, due to the large number of these firearms produced over many years around the world, it is impossible for us to allow for all manufacturing variation. This mount will NOT work for NORINCO / CSI / KSI SKS’s. As with any of our products, it may be returned undamaged for a full refund. Proper tightening of all hardware should result in no movement of the mount during normal firing recoil.

NOTE:

Any scope and/or mount that suffers an impact, should not be trusted to be accurate. If you feel your mount has been compromised, you can still use your original open iron sights. Design subject to change without prior notice. Caution! Improper installation or use may result in damage to property, severe injury, or loss of life. If for any reason this product does not function properly, discontinue use immediately. Always practice proper SAFETY and ensure an UNLOADED condition before beginning installation.

Click here to view the installation video for the SKS Scout Scope Mount

Please call us at 828-665-4427 with any installation questions you may have.

Spent Casing Deflector Model # SKSCD<<DETAILS
(recommended if using a long tube optic)

DUE TO AVAILABILITY, WE REGRET THAT WE CAN NO LONGER OFFER THE MOUNT/SCOPE COMBINATION AT A DISCOUNTED PRICE. SCOPES ARE SOLD SEPERATELY HERE.

The post SKS See Through Scope Mount For Russian, Yugoslavian & Chinese appeared first on Brass Stacker.

•Dovetail Scout Mount for Long Eye Relief (LER) optics on the Mosin Nagant M91/30
•Lowest profile with all steel construction and NO permanent modification required
•Ideal for ProMag™ Industries / Archangel™ Manufacturing OPFOR® AA9130 stock
•Locking tapered fitment to the M91/30 barrel dovetail (under rear sight block)
•Dual jam screws & lateral cross bolts provide triple redundant attachment
•MIL-STD 1913 Picatinny Rail with “yaw” adjustment for barrel dovetail lead off
•Made in America with a 100% Lifetime Warranty

***PLEASE READ SPECS & FITMENT NOTES BEFORE PURCHASING***

There is no need for bent bolt handle with this mount. 

Why consider a “Scout” type setup for your rifle?

A LER (Long Eye Relief) optic, or Scout Scope, mounted forward of the receiver provides a substantial uninterrupted overall field of view. This unconfined environment results in greater situational awareness allowing for fast target acquisition and shots taken with both eyes open. This configuration has additional advantages for bolt action MilSurp (military surplus) rifle platforms as it does not interfere with spent casing ejection, straight bolt handles or stripper clip use.

LOOKS CAN BE DECEIVING – Some notes about the M91/30 barrel dovetail under the rear sight block and fitment of the Go Low™ Scout Mount.

Dovetail Taper

The barrel dovetail is tapered longitudinally.  –  Like the original rear sight block, the Go Low™ mount is designed with a mating dovetail.  It is machined to the nominal* barrel dovetail taper. Once the mount is properly seated, the taper of the dovetail will prevent rearward movement of the mount.  The shallow angle of the dovetail taper creates a self-locking engagement. The supplied lateral cross bolts act as a “backup” to this tight fitment restricting forward movement. The two jam screws engaged through the top of the mount into the upper surface of the dovetail then yield a system of restriction with triple redundancy.

Dovetail “Yaw”

The barrel dovetail often leads off at an angle to the bore axis.  –  The rear sight block itself will exhibit this same “yaw” as it is directly attached to the dovetail. This is not of significant consequence to the utilization of the original rear sight and is often imperceptible to the eye. However, this condition can adversely affect systems that utilize this area as a point of attachment. Should your barrel dovetail “yaw” or lead off to the left or right, the Picatinny Rail on the Go Low mount can be adjusted to compensate up to 1.5° per side. While this may not seem like much, 1.5° over 100 yards is almost 8 feet.

FEATURES:

This product provides for the mounting of a scout scope or other long eye relief (LER) optics to the Mosin Nagant M91/30 rifle without the need to drill and tap the receiver or make any permanent modifications to firearm. It is designed to replace the rear sight block of the M91/30.

Fits:

M9130, M9159

SPECIFICATIONS:

The Go Low™ Scout Mount and MIL-STD 1913 Picatinny Rail are machined from solid steel with a black oxide finish. When installed, the top surface of mount is 11/16” (.6875”) above bore centerline. With the low profile Picatinny Rail installed, total height becomes 1” above bore centerline. The mount weighs 3.6 oz. and the 5-3/4” (approx.) long Picatinny Rail weighs 1.8 oz.

MOUNT DOES NOT INCLUDE SCOPE & RINGS!

*FITMENT NOTES:

We have made every reasonable effort to ensure that this product will fit the Mosin Nagant M19/30 rifle. However, due to the large number of firearms produced over many years from multiple arsenals, it is impossible for us to allow for all manufacturing variation. As with any of our products, it may be returned undamaged for a full refund. Proper installation and tightening of all hardware should result in no movement of the mount during normal firing recoil. NOTE: Any scope or mount that suffers an impact (dropped, hit, etc.) should not be trusted to be accurate. If you feel your mount or optic has been compromised in anyway, discontinue use immediately.

NOTE:

A MAPP (Methyl Acetylene Propadience Propane) gas torch and heavy duty punch may be required to remove existing pins from the rear sight block if they are soldered in place. You can usually find these items at your local hardware or plumbers supply. The application of heat, if done properly, will not cause damage. Keep in mind that you only need to reach the melting point of the solder and that this same temperature was achieved during original construction without adverse effects. Procedure provided in supplied instructions.

Design subject to change without prior notice. Use of Pro Mag™ Industries / Archangel™ OPFOR® logo with permission. Caution! Improper installation or use may result in damage to property, severe injury, or loss of life. If for any reason this product does not function properly, discontinue use immediately. Always practice proper SAFETY and ensure an UNLOADED condition before beginning installation.

DUE TO AVAILABILITY, WE REGRET THAT WE CAN NO LONGER OFFER THE MOUNT/SCOPE COMBINATION AT A DISCOUNTED PRICE. SCOPES ARE SOLD SEPERATELY HERE.

The post Mosin Nagant M9130, M9159 Go Low Scout Scope Mount ONLY appeared first on Brass Stacker.